6EXAP Futaba 6-Channel FM 40MHz/ R136F/ 4xS3003

This is the Futaba 6-Channel 6EXAP FM Stick Radio. Transmitter and R136F receiver
and S3003 servos included.

FEATURES:

• Aileron, Elevator and Rudder dual rate switch – Use this switch to flip
  between two aileron, elevator and rudder control throw settings. The throws
  can be set up however you prefer, but generally, when the switch is up the
  throws are greater (high rate) and when the switch is down the throws are
  less (low rate). This switch also flips between exponential rates (if used).
• Flap control dial/Channel 6 – This dial operates the servo connected to
  channel 6 in the receiver if your model has flaps this is the control used
  to operate them.Aileron/elevator control stick -Mounting point for optional
  neck strap.
• Trim levers (all) -Used to shift the neutral or center position of each
  servo as labeled in the diagram.
• Charging jack – Port for charging the transmitter batteries with the included
  battery charger.
• On-off switch
• DATA INPUT lever – Used to change the values of the various functions displayed
  on the LCD screen.
• Liquid-crystal display screen (LCD) – Displays programming modes and values
  entered.
• MODE key – Used to scroll through and display the ten or eleven(PCM) different
  functions.
• SELECT key – Used to display the values for the current function.
• Throttle-cut button – To use the throttle-cut function, lower the throttle
  stick all the way, then Push the throttle-cut button to fully close the carburetor
  and shut of the engine.
• Throttle/rudder control stick – Operates the servos connected to channel
  3 (throttle) and channel 4 (rudder) in the receiver.
• Trainer switch – Operates the trainer functions. To operate as a trainer
  switch the transmitter must be connected to another transmitter via. a trainer
  cord (available separately).
• Retractable landing gear switch/Channel 5 – Switch operates the servo connected
  to channel 5 in the receiver if your model has retractable landing gear this
  is the control used to extend and retract the gear.
• Antenna – Radiates signals to the receiver. Never fly a model without fully
  extending the antenna or you may create interference to other modelers and
  decrease operational signal range of the transmitter. The antenna may be removed
  and replaced with another in case it is inadvertently broken.

INCLUDES:

• Futaba 6-Channel 6EXAP transmitter
• Futaba R136F Receiver
• Four Futaba S3003 Servo
• Switch Harness
• Manual

SPECS:

Transmitter

• T6EXAP Transmitter with programmable mixing and 6-model memory.
• Transmitting on 40 / 72 MHz band.
• Operating system: 2-stick, 6-channel system
• Modulation: FM(PPM) and PCM
• Power supply: 9.6V NT8S600B Ni-Cd battery or 12V alkaline battery
• Current drain: 250mA

Receiver

• R136F narrow band, FM 6 channel receiver.
• Receiving on 40 / 72 MHz band.
• Type: FM, Dual conversion/FM, Single conversion
• Intermediate frequencies: 455kHz, 10.7MHz/455kHz
• Power requirement: 4.8V or 6V
• Current drain: 9.5mA @ 4.8V
• Size: 1.31 x 1.98 x 0.71″ (33.4 x 50.3 x 18.1mm)
• Weight 0.98oz (27.8g)

Servo

• S3003 standard servo with mounting hardware and servo arm assortment
• Control system: Pulse width control,1.52ms neutral
• Power requirement: 4.8 or 6V (from receiver)
• Output torque: 44.4oz-in [3.2kg-cm] @4.8V
• Operating speed: 0.23sec/[email protected]
• Size: 1.59×0.78×1.41″ [40.4×19.8x36mm]
• Weight: 1.3oz (38.0g)